Traxxas Bandit XL-5 Gearing Guide — FDR, Pinion & Spur Chart

Traxxas Bandit XL-5 RC Gearing & Optimization Guide

Optimizing your gear ratio is one of the most effective ways to balance speed, torque, and electronics longevity in your Traxxas Bandit XL-5 (Brushed / RTR). The relationship between your pinion gear (attached to the motor) and your spur gear (attached to the transmission) dictates how hard your motor has to work — and on a 1/10 basher buggy platform with a 2.72 internal transmission ratio, even a single-tooth pinion change shifts your final drive ratio by 3-5%.

The Traxxas Bandit XL-5 is the brushed RTR configuration of the 2WD Bandit buggy. Its slick front and low-profile rear tires produce the shortest rollout of the Traxxas 2WD family, which on brushed power translates to the punchiest feel of the four trucks on 7-cell Ni-MH — but also the highest torque load on the Titan brushes.

Basher & Monster Truck Durability Notes for the Traxxas Bandit XL-5

Heavy landing impacts on a platform like the Traxxas Bandit XL-5 routinely bend motor mounts out of parallel with the spur, which is the single fastest way to strip a 48-pitch spur gear mid-session. After every big air session, sight down the pinion-to-spur mesh and confirm the motor plate has not shifted — a mount that has moved even half a millimeter will chew teeth within a pack. Just as importantly, check your center differential fluid thickness on a regular schedule; on high-power basher drivetrains the center diff is what manages extreme power distribution between the front and rear axles, and thin or contaminated fluid lets the light end spin up under throttle punch, spiking motor amp draw and cooking spur teeth from the inside out.

🛠️ Essential Tools Required for Gearing Changes

Hex drivers (1.5mm, 2.0mm, or 2.5mm depending on the Traxxas Bandit XL-5 variant)
Paper strip (for setting precise gear mesh)
Infrared temperature gun (crucial for monitoring motor heat after each run)
Threadlock (for the pinion gear grub screw)
Pinion gear puller (recommended when swapping gears on a hot motor shaft)

📋 Comprehensive Gearing & Temperature Guide

1. Understanding Pinion vs. Spur Gear Adjustment

Changing your gears alters your final drive ratio. Installing a larger pinion gear or a smaller spur gear increases top-end speed but increases the load on the motor, causing it to run hotter. Conversely, a smaller pinion or larger spur increases torque and acceleration while lowering top speeds and keeping your motor cool. On the Traxxas Bandit XL-5, this trade-off is amplified by the fixed 2.72 internal ratio — small external changes have a direct thermal consequence.

2. How to Set a Perfect Gear Mesh

Improper gear mesh will quickly strip your spur gear or bind your drivetrain.

Loosen the motor mount screws slightly.
Place a small strip of standard notebook paper between the pinion and spur gear teeth.
Press the gears tightly together and tighten the motor mount screws.
Roll the paper out. The paper should have clean, crisp crinkles without ripping.

Recommended Pinion & Spur Chart

All combinations use a 90T 48-pitch spur. FDR is calculated as (spur ÷ pinion) × 2.72 internal ratio.

Pinion	Spur	FDR	Typical Use
13T	90T	18.83	High-bite carpet / tight indoor
15T	90T	16.32	High-bite carpet / tight indoor
17T	90T	14.4	High-bite carpet / tight indoor
19T	90T	12.88	High-bite carpet / tight indoor
21T	90T	11.66	High-bite carpet / tight indoor

Understanding Pinion & Spur Gears

Stock Bandit XL-5 uses a 15T pinion / 90T spur. Because the buggy is light and geared short, the Titan runs cooler here than on the Stampede or Rustler at the same pinion — some owners run 16T for a bit more top-end without paying a heat penalty.

Rollout Targets

Working Bandit XL-5 rollout with stock buggy tires is around 2.3 inches per motor revolution — the shortest in the family, which is exactly why the brushed motor can lug so hard off the line on Ni-MH.

Motor Temperature Management

Titan 12T on the Bandit XL-5 should stay under 180F (82C). Because the buggy is the fastest of the four trucks, brush wear accelerates from sustained top-end running — inspect the brushes every 4-5 packs and replace at 2mm length.

⚠️ Critical Safety & Temperature Warning

Always use an infrared thermometer to check your motor and ESC temperatures during a run. RC electric brushless motors should never exceed 160°F (71°C). Exceeding 180°F (82°C) risks permanently demagnetizing your motor rotor and frying your Electronic Speed Controller. If your Traxxas Bandit XL-5 is running above these thresholds, you must "gear down" by installing a smaller pinion gear immediately, improve airflow with a larger motor fan, and inspect the drivetrain for binding.

Calculate a custom FDR for your Traxxas Bandit XL-5

The link below opens the calculator with Custom / Other Chassis pre-selected, the Traxxas Bandit XL-5's internal ratio of 2.72 and its recommended battery of 7-Cell Ni-MH (8.4V) already set — just plug in your pinion, spur, motor, and tire to see top speed, runtime, and FDR for your exact setup.

Open calculator with 2.72 ratio + 7-Cell Ni-MH (8.4V) preset →Brushed / 7-Cell Ni-MH (8.4V) stock setup →

🔧 Brushed Motor Maintenance for the Traxxas Bandit XL-5

Brushed motors on the Traxxas Bandit XL-5 are wear items — the carbon brushes, springs, and copper commutator all consume themselves as the truck runs, and 90% of "my truck feels slower" complaints on a brushed RTR trace back to worn brushes or a glazed comm rather than a bad pack or the wrong gearing. Build a five-minute inspection into every 4-5 pack cycles and the stock Titan-class motor will outlast most bearings on the truck.

1. Inspect the carbon brushes

Pop the brush hoods off the endbell and pull the brushes out with a pair of tweezers. New brushes on a 540-size motor are roughly 6-7mm long. Once they wear below 2mm the spring can no longer keep firm contact with the commutator — you get arcing, hot brushes, and a sudden drop in top-end speed at the same gearing. Replace brushes as a pair, never just one, and always with the motor cold.

2. Clean the commutator

A glazed or dirty commutator shows up as reduced pulling power at low speed and a burnt-electronics smell after a hard pack. Remove the brushes, blast the commutator surface with a can of dedicated motor spray (never brake cleaner — it attacks bearing seals), then run a comm stick lightly across the copper segments while spinning the shaft by hand. The copper should come back to a bright, uniform pink; any dark spots or grooves mean the comm needs a true-up on a comm lathe or a motor replacement.

3. Check brush spring tension

Weak springs cause the brushes to bounce at high RPM, which shows up as an intermittent power cut on straights. Compare the spring compression side by side with a spare — if one is noticeably shorter or softer, replace the pair.

4. Break in new brushes properly

After a brush or motor swap, run the truck on a stand (wheels off the ground) on a 6-cell Ni-MH pack for 2-3 minutes at low-to-moderate throttle. This seats the new brush face to the commutator profile before you subject it to full stall torque on a rock face or bash pack.

Rule of thumb on the Traxxas Bandit XL-5: if top-end speed drops noticeably at the same gearing and pack, inspect the brushes and commutator BEFORE you assume the motor is dying — 8 out of 10 times it is a $6 brush set, not a $35 motor.

Ni-MH vs. LiPo on the Traxxas Bandit XL-5

Running a traditional 7-Cell Ni-MH (8.4V) nickel pack on the Traxxas Bandit XL-5 behaves very differently from a modern LiPo of similar nominal voltage. Ni-MH cells sag noticeably under load — a fresh 7-cell 8.4V stick pack measures closer to 7.2-7.6V once the trigger is pinned, which lowers real-world motor RPM and top speed by 10-15% compared to a 2S LiPo bench number. This voltage drop also means the ESC pulls higher current to hold speed, so brushed Titan-class motors on Ni-MH actually run hotter per lap than the same truck geared identically on a 2S LiPo, even though the pack voltage looks lower on paper.

Weight distribution changes too: a 6-8 cell Ni-MH stick or hump pack weighs roughly 380-460 g, versus 220-290 g for a comparable 2S/3S hard-case LiPo. On a short course truck or stadium truck like the Traxxas Bandit XL-5, that extra ~150 g sits low and rearward, softening the chassis' pitch response and loading the rear tires harder on corner exit. Bashers converting from Ni-MH to LiPo almost always need to add a tooth to the pinion (to compensate for the lighter, punchier LiPo delivery) and re-check motor temps after the first pack, because the same FDR that was cool on nickel can heat-soak on a high-C LiPo.

Rule of thumb: on Ni-MH, target motor temps 10-15°F cooler than the LiPo maximum listed above — the sustained current draw is higher, and nickel packs are less forgiving of over-gearing before they thermally cut out.

Traxxas Bandit XL-5 (Brushed / RTR) Gearing Guide